1.22m Hot dip galvanized steel water tank
The hot dipped galvanized steel water tank is defers to the GB code 92SS177 manufactured new type water tank. The manufacture and the installment of tank have no influence of the construction. There are not needed the welding apparatus, the surface is hot dipped galvanized antiseptic treatment. It's artistic durable, prevents two times pollution to water quality and it is beneficial to human health. The water tank meets the construction product standardization, the serration and the factorization request.
This product uses the Q235 steel plate, ramming to1000*1000 and the 1000*500 standard plate, the peripheral drill hole, undergoes hot dipped galvanized processing. When it assembles between the standard plate clamps use the rubber packing and bold fastening.
Specifications
This water tank volume has 24 kinds specifications, select for the design. The engineer also can design according to the water tank's length, width, high then factory assembles.
The inlet pipe, the outlet pipe, the overflow caliber and the position of water tank depends on the design. All around the water tank should have no less than 700mm channels, the bottom and the cover shouldn't be less than 600mm. When it is installed, the bottom and all around between the bottom standard plate's joins must be located on the support.
Application
This product is suitable for the construction water storing, the regulating tank, heating system's inflation water tank, the condensate tank as well as the building construction, the geological prospecting, the industry, the defense project and so on temporarily store water tank.
Installation
1 Material
The sectional panel tank shall consist of 4' x 4' or 1 meter x 1 meter panel manufactured from 1.5mm to 4.0mm thickness according to requirement.
2 Flanges
The sectional panels shall be pressed to double flanges at the angles of 45 degree and 90 degree to the face of the plate on four sides.
3 Reinforcement Method
All tanks are internally braced with angle stays to endure the rigidity of the tank when filled with the water. TheTop panel is supported by top panel support, which shall be made of stainless steel grade 304 or 316 materialaccording to requirement.
Feature
Galvanized Steel Combined Water Tank is punched by Q235 into 2000mm*1000mm, 2000mm*500mm, 1500mm*1000mm, 1500mm*500mm, 1220*1220mm,1000mm*1000mm, 1000mm*500mm, 500mm*500mm, etc standard panels, drilling around, after HDG treatment, assembly at site. When combined, the gap between two standard panels is sealed by silicon pad, connected by bolts.
The product is suitable for storage of building water supply, regulating water tank, expansion of heating system, condensate tank and construction, geological reconnaissance, industrial, national defense engineering and other temporary storage tanks.
Water storage capacity from 1 cubic meter to 3000 cubic meters, height up to 6 meters.
The portable collapsible water tank is an ideal storage solution for outdoor rainwater collection, water storage, fire protection, oil field storage, liquid fertilizer, water treatment, irrigation water storage, and much more. Collapsible water tank is low cost and can be custom sized to suit your project.
| ank Height(mm) |
Thickness of each panel |
| Bottom Panel |
1st layer side panel |
2nd layer side panel |
3rd layer side panel |
4th layer side panel |
Cover panel |
| 1000 |
3# |
3# |
/ |
/ |
/ |
2# |
| 1500 |
3# |
3# |
3# |
/ |
/ |
| 2000 |
3# |
3# |
3# |
/ |
/ |
| 2500 |
4# |
4# |
3# |
3# |
/ |
| 3000 |
4# |
4# |
3# |
3# |
/ |
| 3500 |
4# |
4# |
3# |
2.5# |
2.5# |
| 4000 |
5# |
5# |
4# |
3# |
2.5# |
Accessories
1. Bolt. nut & washers stainless steel 304 material.
2. Sealing material Non-toxic P.V.C foam tape shall be used in between the joints.
3. Covers The tank cover shall be constructed from 1.2mm to 3.0mm of thickness stainless steel 304 material according to the requirement.
4. Ladders and Level Indicator: Internal & external ladder shall be made of stainless steel grade 304 material.
Packing and shipping Detail
packing with pallet or wooden case,to make sure you get the products in good conditions
FAQ
Q1Can i only send you the CAD drawing or 3D drawing , and you make the sample for me to test , it's OK?
A: Yes ,we can make the product that you need based on the sketch drawing or 3D Drawing
Q2:Can I go visit your company?
A:Yes, of course! You're warmly welcome! If you come, please feel free to contact us. We will pick you up!
Q3: You are a factory or trade company?
A: We are a factory which located in dezhou, Shandong, China.
Q4: Do you accept samples order?
A: Yes we can accept.
Q5: Can you make a confidentiality for our project ?
A: Yes of course. We can sign a confidentiality agreement for you.
Audited Supplier 
Audited Supplier 
){kind=link}
){kind=link}